Prentiss Effects

This post is an in depth look at the Ernie Ball VP tone suck mod. It works on all passive Ernie Ball volume pedals and can also be applied to other passive volume pedals. I'll go over why people experience "tone suck" (hint: it's because of impedance) and a step by step on how to install a buffer that prevents this.

I've been looking into making a replacement PCB with these mods built in. If this is something interesting to you then please go fill out this form and let me know.

Now, let's get started!

What it does and why it works #NerdTime

In audio level signals, we look at optimizing voltage transfer to maintain our signal. As the ratio drops, our high end begins to roll off as well. The Ernie Ball VP (and JR) is basically the volume circuit from your guitar and an added output jack for the tuner before the volume pot. The problem with this configuration is that the volume pot in the volume pedal puts a load on your signal which combines in parallel with the input impedance of your amp or the next pedal in your chain and lowers your voltage transfer ratio. Let's look at the math of how that all works.

For starters, your guitar has a high output impedance. Sources vary a lot on what that range is, but Jack Orman and Jack Deville seem to agree that it's somewhere between 10k-40k (and they're both really smart so we'll trust them). I'll use 15k for our purposes. Now standard practices tell us that in order to optimize voltage transfer we want the input impedance of the next object in our signal chain to be at least 10x greater than our output impedance. In fact, the higher we can make the input impedance, the better the transfer will be and less high end will be lost. The reason for this is that your guitar's output impedance can be thought of as a series resistance and the following input impedance as a resistance to ground which creates a voltage divider.

So let's say that we normally have a guitar going into a pedal with a 500k input impedance. That gives us a circuit that looks like this:
We can then look at the voltage divider equation to figure out our ratio. Upon inspection, we can state that if our input signal is assumed to be 1V then we really only need to look at the resistance ratio to figure out our voltage transfer ratio. So by plugging in those numbers we get the following:

So we're going to be seeing about 97% of our signal go through. Great! That 3% that we're losing is coming from our high-end because higher frequencies are effected more by impedance. So the frequencies we're losing are ones we can't really hear.

Now if we add the volume pedal into the signal chain we get a different result.

The pot in the volume pedal is essentially a parallel resistance to our pedal's input impedance. This means that our overall resistance value is going to be lowered. If we do our calculation again then we get this result:

Now we're seeing that we're losing about 8% of our signal. At this point we can start to hear some of that "tone-suck" people talk about, but probably not enough for us to freak out about much. But let's add in that tuner.

When we add in the tuner to the circuit we get a new diagram and equation because of all the parallel resistances. The diagram looks like this now:
Let's go through the equation simplifying along the way:

We're now losing 11% of our signal and that high end is really starting to go away.

In order to prevent this high end loss, we add a buffer in between the input and the split. This turns our high impedance guitar signal, 15k, into a low impedance signal, 10-1k (1). If we plug that value into our crazy tuner equation then we the following:

Boom! We have all audible frequencies and then some to annoy the dog with! This is why the buffer is so useful. It lowers your impedance so drastically that it doesn't matter what comes after, you're going to have a great voltage transfer. Tone Suck Gone! Now let's take a look at doing the actual mod.

Step by Step

Now we'll look at the process of modding your volume pedal with a buffer at the input. I put the buffer on a toggle switch when I do it. This lets me turn off the buffer and still use my volume pedal which makes it so I can use that power jack for something else if I need to. Also, some people use their volume pedal with a Y-split TRS cable as an expression pedal. This won't work if there's a buffer in the circuit. So by putting the buffer on a toggle, it still allows you to use it as an expression pedal if you wanted to.

Aside from the standard tools. You will need the following:

• 1x Completed Buffer Circuit (I use a Klon based buffer, but any good buffer will do)
• 1x DPDT Toggle Switch
• 3x LEDs (of your favorite color)
• 1x 330Ω resistor

The resistor and LEDs are not strictly necessary. Once you have the buffer in place, the actual signal benefits of the mod are done. But  let's be honest, you gotta put LEDs in there so people know you have a super modded volume pedal of awesomeness!

Step 1

Turn over your volume pedal and remove the two screws underneath the black faceplate. Then remove the nuts holding the jacks in place so the faceplate can be removed.

Step 2

Take the faceplate and drill a hole between the input and output jacks for the power jack. Then drill a hole directly above for the toggle switch. Be sure to measure the size of each hole first as they will be different. Go ahead and put the toggle switch and power jack in place when you're done, making sure the toggle moves vertically when switched (I'll go over why later).

Step 3

Solder a wire between the top two lugs of the toggle switch. This will allow you to bypass the pedal when the toggle is in the down position. I do it this way so that if you unplugged your power jack to use on a different pedal and your foot slid off the front of your volume pedal, you can't knock the toggle into a position that would kill your signal.

Step 4

Take the circuit board that the jacks are mounted on and desolder the input jack. You may only need to desolder the tip for this to work. Be patient and don't stay on the solder joint for too long or you may burn the PCB trace.

Note: It may be easier to clip off the tip connection from the jack and then desolder the bit still in the pcb by essentially pushing it through with your soldering iron. This does risk burning the PCB but it can be useful.

Step 5

Bend the tip of the input jack so it doesn't make contact with the pcb and solder a wire from the tip to the middle of the right side of the toggle. Then solder a wire from the other side of the middle of the toggle to where the input jack used to be soldered.

Pro Tip: If you don't have a set of soldering "third-hands" then you can clamp the wire down on the jack using some blue tack or a bobby pin.

Note: If you had to cut the connection to the jack then you will still need to bend it a bit. When you're soldering the wire to the tip, scratch the metal a bit with a knife or some sandpaper to help the solder flow better. You may also want to do the bobby pin trick to keep the wire from sliding around while you're soldering.

Step 6

Find where you want to place your buffer circuit inside the pedal and tape it in place using double sided tape. I place mine above the input jack on the faceplate. Then solder the input and output wires from the buffer to the remaining two lugs on the same sides as each input/output jack.

Note: At this point if you don't want to add the LEDs, you can solder your power and ground buffer connections to the power jack (make sure to connect your power jack's ground to the chassis ground or you'll get hum) and you're done.

Step 7 (Adding LEDs)

Pick three LEDs (same color is usually best) and a 330Ω resistor. I personally love green and blue LEDs for this, but I've seen some awesome purple ones too. You will be putting one in each bottom corner and one in the top center (angled slightly upwards). We're going to take advantage of the ground connections from the jacks in the bottom two corners and solder the bottom LEDs to them in the next step.

Step 8

In the bottom left corner, take the negative end of your LED and push it through the ground connection of the jack while heating that joint with your soldering iron to make the solder flow. Get the LED right up next to the solder joint and make sure that it's a firm connection. Repeat this process in the bottom right corner. 

Step 9

Take the negative lead for the LED in the top center and do the same process you did for the previous LEDs, but push just enough of the negative lead through in order to center it. 

Step 10

Solder one side of your resistor to the positive ends of your LEDs. I find it helps to angle the LED leads towards the center of the pedal and then bend the resistor lead to wherever it needs to go. Also, another time where blue tack or the bobby pin trick can be helpful. 

Step 11

Connect a wire to the other side of your resistor and run it to the power jack. Solder in the power connection from the buffer and the resistor at the same time to make it easier. 

Step 12

Connect your power jack's ground connection to the buffer ground and the chassis ground (you can use one of the input jack's like you did with the LEDs) and you're all done! 

There you go! You now have a tone suck free volume pedal with some awesome LEDs to prove it.


References

1. Jack Orman - http://www.muzique.com/lab/pickups.htm
2. Jack Deville - Mr. Black Pedals Blog - Buffers, Impedance, and Other Internet Lore
3. Endolith - How important is impedance matching in audio applications
4. Impedance Bridging -  https://en.wikipedia.org/wiki/Impedance_bridging
5. Voltage Divider Tutorial - https://learn.sparkfun.com/tutorials/voltage-dividers
6. Parallel Resistor Calculator - http://www.sengpielaudio.com/calculator-paralresist.htm
7. Voltage Divider Calculator - http://www.raltron.com/cust/tools/voltage_divider.asp

The Mod

Parts:

• Joyo Ultimate Overdrive
• 500K Log Potentiometer (link has a drop in replacement for the board mounted one)
• 1K5 Resistor
• 470K Resistor
• 100nF Capacitor

Schematic

Here is a schematic of the changes we'll be making. We'll then go step by step through how to perform the mod.

Steps 

When desoldering, it will probably be easiest to do it from the underside of the board. I recommend marking which components to remove on the underside. Then you can put the board back into the enclosure and use the enclosure to stabilize the board while you desolder.

1.  Desolder the drive pot and replace it with the 500K Log pot. This will give you a smoother  transition through the gain range of the pedal. Alternatively, you can solder a 330K resistor across the outside lugs of the gain pot per the original mod.
2. Solder the 1K5 resistor to the outside lugs of the Tone pot. (You may find it easier to do this on the under side of the board)
3. Solder the 470K resistor to the outside lugs of the Volume pot. (See note in step 2)
4. Remove C9, a 1uF capacitor, and replace it with the 100nF capacitor.
   Note: If you have a board version prior to "2010.11.24" then you'll need to replace C7, which is a 10uF, instead. 
5. If you're board has a version date of "2010.11.24" (which all the recent ones do) then you'll need to remove the germanium diode and turn it around. The silkscreening is wrong and means that only one half of your signal will be clipped if you don't change this. I put sockets on the underside so I can easily swap out different diodes to taste. 
6. Optional: The wires from the footswitch to the main board are cheap and prone to breaking. I recommend replacing all of them with some good wire so it doesn't die on you when you're playing live. 

What it does

The mod is fairly simple as far as theory goes. The original mod by Freekish Blues uses 3 resistors in parallel with the pots to lower their values and thus limit their range. By using a 330K resistor, the gain pot goes from 1M down to 250K. I prefer to just swap it for a 500K Log pot since this is the preferred value on the OCD. Also, the log taper makes it a smoother transition across the gain range so it doesn't need to be limited to just 250K. The volume pot gets reduced in the same way from 500K to 250K.

The tone pot is a bit more interesting. It forms a simple low pass filter with the 100nF capacitor. With the pot turned all the way up the cutoff frequency is originally about 16k. By reducing the value of the pot with the parallel resistor, we get a different cutoff frequency. The 1K5 resistor takes our tone control down to a value of 1.3K which is pretty cool since we can't just go buy a potentiometer of this value. By doing this the cutoff frequency becomes roughly 122K. Now, to be fair, you can't hear about 80% of those frequencies...but it is brighter. Also, since the tone pot is a log taper, you're going to have a really wide range of usable settings across the whole knob.

Lastly, the capacitor change just limits how much bass is allowed to pass through the circuit before hitting the tone control.

I hope you found this a helpful bit of info. If you did then leave a comment telling me what you found most useful so I can focus on those things in later posts. Also feel free to leave a link to any pics of your mods.

The 1776 Unicorn Breath Buffer is based on the buffer circuit in the famous Klon Centaur but with a little something extra that makes it a really cool/handy little project.  I'll be going over the bare bones of why you would want a buffer in your signal chain and then what makes the Unicorn Breath unique

What a buffer does...

Everyone's heard the debate over buffered vs. true bypass pedals so I won't be going over that in this post. But general consensus is that true bypass is great, unless you have a bunch of cabling and pedals between you and your amp. The extended cable lengths (through cable capacitance and signal impedance) create a low pass filter that cuts off more of your high end as the cable length increases. A buffer near the beginning of your signal chain alleviates this issue by lowering your signal impedance which raises the cutoff frequency of the high pass filter. I won't go into any more detail on that here, but if you'd like to know more then leave a comment below. On to the board!

Unicorn Breath Buffer

There's a bunch of reasons I like the Unicorn Breath. It's designed around being a DIY project so there are some aspects of the board layout that are really geared towards the builder. That being said, I'm just going to go through my favorite things about it.

1. It's really small. The board itself is only 1" x 1". This makes it perfect for small boxes like the 1590A or 1590LB. It's also a great size for modding pedals like the Ernie Ball VP JR because it fits neatly inside the faceplate. 
2. It has the LED board mounted. I like this because I can just wire in the LED without thinking. Plus I can mount my LED without a bezel if I want to. 
3. Uses a dual op-amp. Most Klon buffers call for a single op-amp. This uses a dual op-amp pinout which is a more common part that you're more likely to already have (hooray for no special order parts!).
4. Voltage buffer. Your reference power voltage is buffered. This means that if you were to use the Vref on the board in another circuit, then the current draw wouldn't be an issue. It's not strictly necessary for this circuit, but it's a nice feature and uses the other half of the op-amp.
5. Extra ground ports. I like have extra places for ground so I can wire my power supply to the board as well as my jacks rather than having to snake wires all over the place. Plus most people don't wire a buffer as true bypass, so you can do all your connections to the board.  
6. Tight layout design. There's no wasted space on the board. All the components are neatly aligned with no strange spaces in it. It's just quite nice to look at both before and after it's been populated.

As far as sound goes, it's a buffer. Because it's IC based it's going to be unity gain (transistor buffers tend to have a tiny amount of loss). If you aren't currently running a buffer somewhere in your signal chain then build one of these. You'll get some high end back that you didn't have before which may mean tweaking your knobs a bit, but it also means you'll get consistent sound regardless of cables or number of pedals.

Overall, I really like this board. It's an incredibly useful circuit and the layout is just great. It can fit in a small box that won't take up a bunch of room on your board and your getting a great quality IC buffe. Plus, it's a fun, quick build due to the low parts count and layout. 

Here you'll find my most up-to-date list of resources for parts. There's also a description of each of the vendors with stuff to look for and avoid from each. Lastly, there will be a breakdown of how I usually order parts for a build.

Vendors 

Tayda Electronics

This is a great resource for passive components (resistors, capacitors, potentiometers, etc.). They are based out of Colorado but also have a location in China that handles a lot of their orders. I've never had to wait more than a week for a shipment to arrive and I live on the east coast.

They have the lowest prices of anyone I've seen for components in general too. Most of their potentiometers come with a plastic covering on the back (a.k.a pot condom) that prevents your PCB from grounding out on them. In addition, you can buy resistors in packs of 10 for as low as $0.01/each. They have a good selection of capacitors (film, box, electrolytic, monolithic ceramic, and ceramic disc). There's also a decent selection of axial caps that carry some nice mojo to them. I also like the selection of opamps they carry and the TC1044SCPA charge pump all of which are incredibly well priced.

This is a great place if you really want to try something out without putting a bunch of money into it. There's a minimum order of $5 but that usually gets you at least a pedal's worth of parts.  Their customer service is quite good as they usually respond within a day. If they get something mixed up in your order they will usually give you a nice store credit or refund (store credit is usually higher).

On the downside, some of their transistors and diodes, mostly JFETs like the J201 and 2N5457 as well as germanium diodes, have been proven to be counterfeits. I highly doubt that was intentional on their end. The Chinese market, where they get their parts from, is flooded with fakes so it can be quite hard to discern the real ones sometimes. Plus those components can still work in your build, you just have to bias the JFETs properly and try different diode combinations.

Their enclosures can sometimes be on the cheap side. However, they are starting up a new finishing department which could be really cool. They do already provide enclosures in certain colors and buffed.

What to buy:

• Resistors
• Capacitors
• Diodes
• Transistors
• Opamps
• Potentiometers
• Power Jacks
• Wire (stranded and solid core) 
• LEDs (and bezels)
• Knobs
• Sockets (to swap out ICs, transistors, diodes, etc)

What to watch out for:

• JFETs
• Germanium components
• Bare enclosures
• Input Jacks

BLMS

Lawrence Scaduto runs the best shop on the market for enclosures, switches, input jacks and cool knobs. He also has one of the most hilarious names in the industry: Bitches Love My Switches. Aside from that, Lawrence also carries some helpful extras like daisy chains, patch cables, 3PDT daughterboards, etc.

To top it all off, if you live in the US then he does flat rate shipping on all his items. I've purchased 50 3PDT switches, 5 true bypass looper enclosures, 120 input jacks, and shipping only ever costs $5.99. He usually ships same day and I've never been waiting more than 4 days for anything I've ordered.

Get on his mailing list as he does updates on new products and sends out sales on items he's clearing out.

What to buy:

• Anything and everything.

What to watch out for:

• Nothing. He lets you know what the quality of each item is in its description.

Small Bear Electronics

Small Bear is one of the most recommended sites for builders. They have everything you need and then some. If there's an obscure part you need for your germanium fuzz then they have it. This is where I go for more obscure or out of production ICs and transistors. You can purchased matched JFETs and germanium transistors for fuzz builds (they even sort them by what type of fuzz they'll work well in).

The one downside is that they are a bit pricier than other retailers. But considering you won't have to buy 15 germanium transistors to find two that match for your fuzz build it's worth the extra cost.

What to buy:

• Germanium anything
• Specialty ICs
• Finished enclosures

What to watch out for:

• Nothing in particular. You'll probably want to buy passive electronics elsewhere because of cost. But everything Small Bear sells is good quality.

Mammoth Electronics

Mammoth Electronics is another one of the more popular sites for DIYers. It's geared specifically towards guitar effects rather than sites like Tayda and is really easy to navigate. They have a wide selection of effects kits and partner with some really great PCB designers like Grind Customs FX. On top of that, there's a fantastic selection for enclosures. They have the typical variety which can all be custom drilled and painted for you (for a reasonable fee) and a huge selection of other sizes as well.

Their IC and transistor selection is top notch as well. There's no counterfeit parts to be found here and have a good selection of discontinued JFETs (J201 and 2N5457) required by a lot of amp-in-a-box builds. They also have one of the widest switch selections available. Their 3PDTs are differentiated by grades rather than the standard "Taiwan Blue" switches available at most other retailers.

Mammoth is a bit pricier than sites like Tayda but that's mostly due to being a US based business. While Tayda saves on overhead by employing some overseas workers, Mammoth is based out of Oklahoma and does all of it's own custom orders (mostly enclosures) in house for quality control. They also have to factor in things like parts testing to make sure they aren't sent a batch of fakes, which does add cost. So while your order may be a bit pricier from them, you know what you're getting is the best quality out there.

What to buy:

• Enclosures
• Transistors
• ICs
• DIY Kits
•  Switches

What to watch out for:

• Nothing. Although your passive electronics are usually not a quality concern so you can buy from places like Tayda for a much lower price (order double if you're concerned and it will probably still be cheaper).

Summary by Parts

Passive Electronics

Resistors - Tayda Electronics
Capacitors - Tayda Electronics
Potentiometers - Tayda Electronics
Sockets (for parts swapping) - Tayda Electronics

 Active Electronics

Transistors - Tayda Electronics & Mammoth Electronics
Opamps - Tayda Electronics & Mammoth Electronics
Specialty ICs - Small Bear Electronics

Hardware

Input Jacks - Bitches Love My Switches
Power Jacks - Tayda Electronics
Enclosures - Bitches Love My Switches & Mammoth Electronics
Footswitches - Bitches Love My Switches & Mammoth Electronics
Knobs - Bitches Love My Switches & Tayda Electronics
Toggle Switches - Tayda Electronics & Mammoth Electronics
Wire - Tayda Electronics

My Order Process

This is how I typically separate parts of my order for a build.
Tayda Electronics - Resistors, capacitors, potentiometers, ICs, general purpose transistors (not JFETs), wire, toggle switches, sockets, and knobs.
Bitches Love My Switches - 3PDT, enclosure (if I want a basic one), input/output jacks, thinline power jack (since I don't use batteries)
Mammoth - JFETs, specialty diodes, enclosure (if I want something very specific or pre-painted).


Now that you've got all your parts, it's on to the Build Procedure

The two most popular ways of building guitar effects on are PCBs (Printed Circuit Boards) and veroboard (a.k.a. Stripboard). I'll go through the pro's and con's of each so you can decide which is best for you. So let's start with...

Veroboard (a.k.a. Stripboard)

Veroboard is essentially a series of parallel copper strips with holes drilled through them. Any components soldered in the same row will share a connection. You can cut the copper traces on the veroboard to expand the number of possible junctions for components or you can run jumper wires from one to another to expand a row. A lot of DIY sites use veroboard to create layouts. The reason being that it's fairly easy to modify and adapt to different circuits. Since veroboard was developed as a prototyping tool, it isn't bound to doing one circuit or style or design. It's also very inexpensive (0.66 a piece at Tayda Electronics)

The downside of veroboard is that it can be finicky. If your circuit doesn't work then it could be that you didn't cut the trace properly, or you accidentally soldered two rows together, or  you soldered your jumper wires to the wrong rows, etc. The board becomes something you have to troubleshoot in addition to the normal checks for a PCB.

In the end, the price and adaptability of veroboard makes it a very common framework for DIYers. If you decide to mode your Tubescreamer with a couple more resistors then you can simply add another row or column to the layout and your good to go. Just be ready to spend a little more time when fault diagnosing your circuit if it doesn't work right away.

PCBs (Printed Circuit Boards)

PCBs are usually designed for a single circuit. Traces are etched into copper and then a coating and silk screen are placed over top to prevent the traces being damaged (amongst other things). Some cool things about PCBs are that they often have board mounted components like switches and potentiometers which saves having to solder a bunch of wires. It also makes fault finding a lot easier since your layout ends up being a lot cleaner since you're not having to trace as many wires around the enclosure. If the board doesn't work then they are usually easier to troubleshoot than veroboard since you know the layout works (if you're buying from a good PCB vendor) so it narrows things down. In addition, they also have figures on the top showing you where all of your parts go so it can be significantly faster to populate a PCB with parts since you don't have to count out to which hole you're putting the part in like you do on veroboard.

On the other hand, they are pricier than stripboard because they have to go through a design and fabrication process. But they are much more reliable because of this. Designers also have an easier time implementing noise reducing techniques than in veroboard so you can get a quieter circuit.

I thoroughly enjoy building a pedal from a well designed PCB (although having veroboard is great when I want to build something in a hurry). They usual work the first time around and if they don't then you know you screwed something up. If you're looking for a good place to order PCBs then here are a couple of my favorites.

• 1776 Effects
• Aion Electronics
• Fuzz Dog
• Madbean Pedals 

Once you've decided which way you want to build, you can start looking at Parts Sourcing

Alright, let's look at what materials you're going to need to get started

Soldering Iron

This one is rather apparent. You're going to want something that will last you for a few builds and not fall apart on you. DO NOT BUY FROM RADIOSHACK! Radioshack soldering irons will corrode really quickly and will only last you about 2-3 builds. I bought one from Harbor Freight Tools and it only lasted me about 5 builds. I suggest getting something that is variable temperature so you can control how much heat you're applying to different parts (you're going to want more heat when you're desoldering a part than when you're trying to solder it initially). I recommend a Weller variable temp soldering iron. They're a reputable brand and a good soldering iron from them is only around $40.

I personally use a Stahl Variable Temp soldering station and it's been great. It's dirt cheap and it's held up really well, plus I can change the tip of the soldering iron if I need to for different projects.

Solder

Get yourself some good solder. I recommend 60/40 tin/lead ratio solder. It's very easy to work with and it's the most recommended kind of solder I've seen across the different forums and YouTube videos I've watched. I personally use Kester 44 Rosin Core Solder 60/40 .031 for my projects. The .031" is the perfect size for the small parts you'll be soldering together because it will melt quickly (which you want) and it's not wasteful like using a thicker solder.

Solder Wick/Sucker

This is what's going to save your life when something goes wrong. You've finished your circuit and realize "I put that capacitor in backwards!". With a solder wick or solder sucker you can remove the solder from the joints you created and just pop the part back out. I highly recommend a solder sucker instead of a solder wick because it's a bit faster (the solder sucker sucks up the heated solder like a vacuum while the solder wick tries to pull the solder onto a braid of small wire instead of your joint).

I use this solder sucker. It's been good to me. Plus, if any part fails you can get a replacement rather than having to buy the whole thing again.

Soldering Iron Tip Cleaner

This one isn't exactly necessary, but I find it very useful. When you're soldering you're going to need to clean the tip of your soldering iron between solder joints. Now you can do this by wiping the tip on a damp sponge (there's a sponge holder on the iron's I linked to earlier) or you can get a tip cleaner. This is simply a brass mesh of wire that you brush your soldering iron on in order to clean it. I find this a lot more convenient and feel that it allows you to keep your soldering iron in good condition longer. Either of these are great: Hakko and Aoyue.

These are all the materials you'll need to be able to get started once you order some electronic components and wire. I order all my components and wire from the same place so I'll go into that in the next post.

At the time of this post the cumulative cost of these four items is just under $75 ($73.25 to be exact).

BONUS

 You can strip wires with a pocket knife or any pair of wire cutters if you're careful. However, your life is going to be a lot happier if you have a good wire stripper. I use the Irwin Automatic Wire Stripper (I've also heard good things about the one by Neiko). It's only around $20 and will adjust to whatever gauge of wire you're using automatically. Plus it has an adjustable bit at the end that let's you strip the same length every time. Having it has cut down on my build times significantly and it's just great. I can't recommend it enough. (Side Note: with the wire stripper, your total would still only be $93.23)

Now that you've got your parts, it's time to decide your Build Method (PCB or Veroboard)

I'll be honest, I started building guitar effects because I couldn't afford the originals. I'm a poor college student and, at the moment, my time is worth far less to me than my money so cloning a pedal is worth my time and fits my budget. But that's an important factor with this kind of work. I want to spend this post examining whether or not you should start building your own effects. So without further ado, let's dive in and answer a few questions (and you really need to be honest with yourself here).